- 您现在的位置：买卖IC网 > Sheet目录221 > DS1921G-F5# (Maxim Integrated)IBUTTON THERMOCHRON F5
DS1921G
Thermochron iButton Device
Overdrive-Skip ROM [3Ch]
On a single-drop bus this command can save time by
allowing the bus master to access the memory/control
functions without providing the 64-bit ROM code. Unlike
the normal Skip ROM command, the Overdrive-Skip
ROM command sets the DS1921G in the overdrive
mode (OD = 1). All communication following this com-
mand must occur at overdrive speed until a reset pulse
of minimum 480μs duration resets all devices on the
bus to standard speed (OD = 0).
When issued on a multidrop bus, this command sets all
overdrive-supporting devices into overdrive mode. To
subsequently address a specific overdrive-supporting
device, a reset pulse at overdrive speed must be
issued followed by a Match ROM or Search ROM com-
mand sequence. This speeds up the time for the
search process. If more than one slave supporting
overdrive is present on the bus and the Overdrive-Skip
ROM command is followed by a read command, data
collision occurs on the bus as multiple slaves transmit
simultaneously (open-drain pulldowns produce a wired-
AND result).
Overdrive-Match ROM [69h]
The Overdrive-Match ROM command followed by a 64-
bit ROM sequence transmitted at overdrive speed
allows the bus master to address a specific DS1921G
on a multidrop bus and to simultaneously set it in over-
drive mode. Only the DS1921G that exactly matches
the 64-bit ROM sequence responds to the subsequent
memory/control function command. Slaves already in
overdrive mode from a previous Overdrive-Skip or suc-
cessful Overdrive-Match ROM command remain in
overdrive mode. All overdrive-capable slaves return to
MASTER Tx "RESET PULSE"
V PUP
V IHMASTER
V TH
V TL
V ILMAX
ε
standard speed at the next reset pulse of minimum
480μs duration. The Overdrive-Match ROM command
can be used with a single or multiple devices on the
bus.
1-Wire Signaling
The DS1921G requires strict protocols to ensure data
integrity. The protocol consists of four types of signaling
on one line: reset sequence with reset pulse and pres-
ence pulse, write-zero, write-one, and read-data. Except
for the presence pulse, the bus master initiates all these
signals. The DS1921G can communicate at two different
speeds: standard speed and overdrive speed. If not
explicitly set into the overdrive mode, the DS1921G
communicates at standard speed. While in overdrive
mode, the fast timing applies to all waveforms.
To get from idle to active, the voltage on the 1-Wire line
needs to fall from V PUP below the threshold V TL . To get
from active to idle, the voltage needs to rise from
V ILMAX past the threshold V TH . The time it takes for the
voltage to make this rise is seen in Figure 14 as “ ε ” and
its duration depends on the pullup resistor (R PUP ) used
and the capacitance of the 1-Wire network attached.
The voltage V ILMAX is relevant for the DS1921G when
determining a logical level, but not for triggering any
events.
The initialization sequence required to begin any com-
munication with the DS1921G is shown in Figure 14. A
reset pulse followed by a presence pulse indicates the
DS1921G is ready to receive data, given the correct
ROM and memory function command. If the bus master
uses slew-rate control on the falling edge, it must pull
down the line for t RSTL + t F to compensate for the edge.
MASTER Rx "PRESENCE PULSE"
t MSP
0V
t RSTL
t PDH
t PDL
t REC
t F
t RSTH
RESISTOR
Figure 14. Intitialization Procedure: Reset and Presence Pulses
Maxim Integrated
MASTER
DS1921G
31
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DS1921H-F5#
IBUTTON THERMOCHRON F5
DS1921K#
KIT IBUTTON THERMOCHRON
DS1922E-F5#
IBUTTON TEMP LOGGER 4KBit F5
DS1922L-F5#
IBUTTON TEMP LOGGER
DS1923-F5#
IBUTTON TEMP/HUMIDITY LOGGER F5
DS1961S-F3#
IBUTTON EEPROM 1KBit F3
DS1963S-F5+
IBUTTON MONETARY SHA-1
DS1971-F3+
IBUTTON EEPROM 256KBIT F3
相关代理商/技术参数
DS1921G-F5#W
功能描述:iButton RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1921G-F5/A0C
功能描述:iButton
RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1921G-F5/A12
功能描述:iButton
RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1921G-F5/A12-W
功能描述:iButton
RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1921G-F5/A14
功能描述:iButton
RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1921G-F5/A15
功能描述:iButton
RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1921G-F5/A17
功能描述:iButton
RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated
DS1921G-F5/A1B
功能描述:iButton
RoHS:否 存储类型:SRAM 存储容量:512 B 组织: 工作电源电压:3 V to 5.25 V 接口类型:1-Wire 最大工作温度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封装 / 箱体:F5 MicroCan 制造商:Maxim Integrated